We founded in 1988, with 32 years'experience in research development and manufacture of industrial boiler. Our boiler are saled for more than 100 countries and regions like Egypt, Ethiopia, Congo, Mauritius, Tanzania,South Africa, Mexico, Ireland, Indonesia etc.

- Hold the ASME "S" and "U" Certificates and have earned ISO9001:2000 Certification.
- High efficiency, low back pressure, ultra-low NOx emissions.
- Elegant design with low surface temperature and low heat dissipation
- Covers an area of 150 thousand square meters, with an annual production capacity of 2000 industrial boilers and 25000 tons of steam.

7*24 hours online service：zhulin@zozen.com

Get Free Quote-
### WNS gas / oil fired boiler

Product Thermal Capacity: 1 - 20 t/h

Working Pressure: 0.7 - 2 Mpa -
### SZS gas / oil fired boiler

Product Thermal Capacity: 20 - 110 t/h

Working Pressure: 1.25 - 5.3 Mpa -
### DZL biomass fired steam boiler

Product Thermal Capacity: 2 – 20t/h

Working Pressure: 1 - 2.5 MPA -
### SZL biomass fired steam boiler

Product Thermal Capacity: 4 - 35 t/h

Working Pressure: 1.0 - 2.5 MPA

Natural Gas Furnace Savings Comparison This calculator will make an estimate of how long it will take to pay back your investment in a new natural gas furnace. Furnace Information

The following article will guide you about how to calculate boiler efficiency by indirect method. Definition of Boiler Efficiency: The boiler efficiency is defined as the ratio of heat actually used for producing steam in a certain period to the heat supplied in the furnace during the same period.

Mar 17, 2015· Steam, Boiler, and Blowdown Pressure are the same. Combustion Efficiency is the % of fuel energy that is directly added to the feedwater and not otherwise lost or used. Blowdown Rate is the % of incoming feedwater mass flow rate that leaves the boiler as a saturated liquid at boiler pressure.

Base model - Values represent a 1,000,000 Btu/hour gas-fired, hot-water boiler operated for 1,500 full-load hours per year with a thermal efficiency of 80%. The performance of this standard unit is based on ASHRAE 90.1-2007. Thermal efficiency (E t) - Represents a boiler's energy output divided by energy input as defined by ANSI Z21.13. A boiler's thermal efficiency rating should be used to

Nov 24, 2016· 1) Boiler Efficiency by Direct Method: Where the energy gain of the working fluid (water and steam) is compared with the energy content of the boiler fuel. 2) Boiler Efficiency by Indirect Method : Where the efficiency is the difference between the losses and the energy input.

The improvement in the boiler efficiency depends on the flue gas temperature. • Use economizers to transfer energy from stack flue gases to incoming feedwater. As a rule of thumb, a 1% increase in the boiler efficiency is expected for each 5°C (9°F) increase in the feedwater temperature. •

1) "Net stack temperature" is temperature difference between flue gas temperature inside the chimney and room temperature outside the burner. Flue Gas Loss with Oil Combustion. The relation between temperature difference in flue gas and supply air, the CO 2 concentration in the flue gas, and the efficiency loss in the flue gas oil combustion, is expressed below:

Aug 29, 2017· Simply guide to calculate boiler efficiency, including combustion efficiency and both direct and indirect method of boiler thermal efficiency. Boiler efficiency is a quantity that indicates the relationship between input energy entering the boiler with output energy produced by the boiler.

ASME PTC-4 – Indirect Method: Stack Loss Method This method approximates the stack losses of a boiler to estimate boiler efficiency. Parameters The parameters needed to calculate this method are given below. These data are calculated during source testing. 1. Stack temperature (T Stack) 2. Dry oxygen in flue gas (O 2,Dry,%) in percent

Boiler efficiency may be indicated by. Combustion Efficiency - indicates a burners ability to burn fuel measured by unburned fuel and excess air in the exhaust; Thermal Efficiency - indicates the heat exchangers effectiveness to transfer heat from the combustion process to the water or steam in the boiler, exclusive radiation and convection losses; Fuel to Fluid Efficiency - indicates the

File Size: 299KB TLV CORPORATION is a proud member of the Fluid Controls Institute (FCI), a non-profit association of fluid control equipment manufacturers. FCI has distinguished itself in the technical advancement of the fluid control industry through the development of standards to promote the production of higher quality, more useful products.

If you have any problems about our product and service,please feel free to give your inquiry in the form below. We will reply you within 24 hours as soon as possible.Thank you!

- WNS gas / oil fired boiler
- SZS gas / oil fired boiler
- DZL biomass fired steam boiler
- SZL biomass fired steam boiler
- WNS hot water boiler
- SZS hot water boiler
- DHL biomass fired steam boiler
- SZL coal fired steam boiler
- DHX CFB steam boiler
- DZL coal fired hot water boiler
- YLW thermal oil heater
- YQ(Y)L thermal oil heater

- 2.8 MW Wns Projects
- 15 tph Szl Projects
- 15 tph Szs Projects
- 2.1 MW Yqw Projects
- 6 tph WNS Project
- 40 tph SZS Project
- 2tph WNS project
- 25tph SHX project

- calculate the heating surface of a boiler
- boiler capacity calculate with heating surface
- calculate boiler size
- calculate bed heigh in cfbc boiler
- calculate water discharging from boiler
- in a process plant steam line drawn from the boiler to process vessel is covered with 38 degree celsius calculate the heat energ
- calculate steam boiler efficiency
- formula to calculate quantity of gas with known energy in boiler
- calculate capacity of thermo oil heater for stenter m c of with 2500 mm per hour
- boiler capacity calculate

Are You Looking for A Consultant?
ONLINE SERVICE