MENU

explain why the temperature of boiler exhaust gases should be maintained above minimum value

We founded in 1988, with 32 years'experience in research development and manufacture of industrial boiler. Our boiler are saled for more than 100 countries and regions like Egypt, Ethiopia, Congo, Mauritius, Tanzania,South Africa, Mexico, Ireland, Indonesia etc.

  • Hold the ASME "S" and "U" Certificates and have earned ISO9001:2000 Certification.
  • High efficiency, low back pressure, ultra-low NOx emissions.
  • Elegant design with low surface temperature and low heat dissipation
  • Covers an area of 150 thousand square meters, with an annual production capacity of 2000 industrial boilers and 25000 tons of steam.

7*24 hours online service:zhulin@zozen.com

Get Free Quote

OUR PRODUCTS

Explore Recent Work

Exhaust Gas Boilers And Economisers working procedu

The minimum temperature of 140 degree C should be kept, when running with the exhaust gas bypassing the economiser. iii) Operation 1) Exhaust gas boiler circulation must be maintained at all times. This is to maintain tube temperature and prevent “cold end” corrosion of tube and fins.

2. BOILERS - Bureau of Energy Efficien

2. BOILERS Bureau of Energy Efficiency 27 Syllabus Boilers: Types, Combustion in boilers, Performances evaluation, Analysis of losses, Feed water treatment, Blow down, Energy conservation opportunities. 2.1 Introduction A boiler is an enclosed vessel that provides a means for combustion heat to be transferred into water until it becomes heated water or steam.

Low Temperature Corrosion in Boiler and Its Preventi

Condensation of these acids results in metal wastage and boiler tube failure, air preheater corrosion, and flue gas duct corrosion. In order to avoid or reduce the cold end corrosion the gas temperature leaving the heat transfer surface in boiler is kept around 150 degrees centigrade, ranging from 120 to 155.

Diesel Exhaust G

Jan 01, 2018· Shown are temperatures from vehicle chassis dynamometer certification cycles (cold start FTP 75 and US06) and a heavy-duty engine dynamometer certification cycle ().The T 90, T 50, and T 10 values are defined as temperatures below which exhaust gas temperature is 90%, 50%, and 10% of the time, respectively. Also shown is the time, t 200°C, from the cycle start to the point where exhaust gas

Boiler Components - Marine Engineeri

Where T1 is the maximum temperature in a cycle ( kelvin ), and T2 is the minimum temperature in a cycle. For the steam plant these equate to boiler outlet temperature and the exhaust temperature …

Auxiliary Boilers - LinkedIn SlideSha

Jun 08, 2018· The circulation of water through the exhaust gas boiler must be maintained after stop of the main engine for the following reasons: The boiler is kept heated by the oil fired boiler(s) and therefore ready for start of the main engine. A soot fire may develop even after stop of the main engine, and if the tubes are not properly cooled, this may

Combustion Fundamentals - Industrial Wiki - odesie by Te

The proper value of excess air is a function of boiler load, fuel quantity, and air leakage through idle burners, steam temperature, flame stability, and energy losses. To understand the combustion process in a boiler, we will first investigate the process of combustion.

Everything You Need to Know About Combustion Chemist

The Net Stack Temperature is the temperature that the gases are raised above the temperature of the primary and secondary air, The modulating boiler is a combustion system that adjusts its firing level and steam production to meet a changing output demand. the stack temperature must be maintained above the dew point.

Steam Sterilization Principles - IS

sure should not be more than twice the chamber pressure at the desired temperature. Superheat is also created when saturated steam passes over a surface at a higher tempera-ture. The sterilizer jacket temperature should always be set slightly below the chamber sterilization temperature to avoid superheating of the steam as it enters the chamber. 4.

Water Handbook - Preboiler & Industrial Boiler Corrosi

The pH or alkalinity level maintained in a boiler system depends on many factors, such as sys-tem pressure, system metals, feedwater quality, and type of chemical treatment applied. The corrosion rate of carbon steel at feedwater temperatures approaches a minimum value in the pH range of 9.2-9.6 (see Figure 11-9). It is important to monitor the

BOILERS | Energy-Models.c

The most common boiler of this class is a three-pass unit with two sets of fire-tubes and with the exhaust gases exiting through the rear of the boiler. The flue gas exit tempera ture from a boiler is usually maintained at a minimum of 200 When the flue gas temperature rises about 20 o C above the temperature for a newly cleaned boiler

What Can I Do For You?

Send us your inquiry
Leave Us Message

You can send a message to us by this email to zhulin@zozen.com

If you have any problems about our product and service,please feel free to give your inquiry in the form below. We will reply you within 24 hours as soon as possible.Thank you!

  • Boiler type
  • Name
  • email
  • Phone or Whatsapp
  • message
I accept the Data Protection Declaration
Are You Looking for A Consultant? ONLINE SERVICE
totop