MENU

pinch point in exhaust gas boiler

We founded in 1988, with 32 years'experience in research development and manufacture of industrial boiler. Our boiler are saled for more than 100 countries and regions like Egypt, Ethiopia, Congo, Mauritius, Tanzania,South Africa, Mexico, Ireland, Indonesia etc.

  • Hold the ASME "S" and "U" Certificates and have earned ISO9001:2000 Certification.
  • High efficiency, low back pressure, ultra-low NOx emissions.
  • Elegant design with low surface temperature and low heat dissipation
  • Covers an area of 150 thousand square meters, with an annual production capacity of 2000 industrial boilers and 25000 tons of steam.

7*24 hours online service:zhulin@zozen.com

Get Free Quote

OUR PRODUCTS

Explore Recent Work

Techno-economic analysis on a new conceptual design

1. Introduction. The temperature of boiler exhaust flue gas normally ranges from 120 to 150 °C in coal-fired power plant (CFPP). The heat loss of exhaust flue gas accounts for approximately 50–80% of the total boiler heat loss and 3–8% of the total energy input of CFPP .This means that recovering waste heat from boiler exhaust flue gas could improve boiler efficiency and reduce emitted

Difference Between Heat Recovery Steam Generators (HR

The steam turbine or a downstream process uses the steam. The term HRSG refers to the waste heat boiler in a Combined Cycle Power Plant. In its basic form these are bundles of water or steam carrying tubes paced in the hot gas flow path. These recover the heat from the gas to generate superheated steam, hence the name Heat Recovery Steam Generator.

What are the procedures for a boiler blow - MarinersPoi

Oct 08, 2019· Open boiler blowdown valve gently. Control the blowdown rate using intermediate valve.(while blowdown keep an eye on gauge glass, in my ship we use blowdown for 120 seconds every alternate day) (however the blowdown rate depends on boiler water test report) Once blowdown is done close intermediate valve,then boiler blowdown valve.

CHP | Combined Heat and Power Exhaust Heat Exchangers a

Cogeneration or CHP (combined heat and power) is the process of recovering exhaust heat that is wasted when an engine runs to produce electricity or other process. Cain Industries manufactures exhaust heat exchangers and heat recovery steam generators (HRSG) for natural gas engines, diesel engines, gasoline engines, turbines, microturbine

Pinch Point Temperature Difference - an overvi

The binary power cycle uses perfluoropentane, C 5 Fl 12, as the working fluid.The evaporator pressure is 0.5 MPa and the condensing temperature is 50 °C. The preheater-evaporator pinch-point temperature difference is 5 °C and occurs at the bubble point of the C 5 Fl 12.The dead state is at 20 °C and 0.1 MPa.

Gas & Diesel Cogeneration Systems - Cain I

Cain Industries offers an extensive selection of cogeneration systems specifically designed for gas and diesel engine, gas turbine and micro turbine generator retrofit applications. We offer over 500 standard products to choose from and will provide a comprehensive analysis and quotation to …

Exhaust Gas Steam Boiler - Lars Josefss

Exhaust Gas Boilers also known as Exhaust Gas Economizers, with extended heating surface, used for waste heat recovery in motor ships. A diesel engine loses approximately 30% of the energy to the exhaust gases. A turbocharger recover some of it, but there is still heat losses that can be recovered by means of an Exhaust Gas Boiler, EGB.

Efficiency of HRSG within a Combined Cycle wi

pinch point GT exhaust gas FIGURE 4. Heat consumption versus temperature diagram for the HRSG Conclusion The performances of the COM-GAS code are shown in this report. The code is underdevelopment, nevertheless, as a first general consideration, one can say that gasification

Exhaust Gas Boilers | Clayt

Exhaust Gas Boilers The Clayton Heat recovery boiler operates on the same tried and tested principle as the world famous Clayton Steam generator. It is therefore the most compact, efficient, responsive and safest means of producing high quality steam or hot water from waste gas streams.

INFLUENCE OF PINCH AND APPROACH POINT ON

Influence of pinch and approach point on construction of a HRSG in a combined cycle 77 Bg – flow rate of combusted fuel burned into the combustion chamber of the gas turbine cycle, m3/s; Q2 – heat flux lost in the condenser with cooling water, kW; Qcs – thermal heat flow of the secondary circuit, kW; Qd – thermal heat flow available, recoverable, of the flue gas evacuated from the

Alfa Laval - Aalborg H/

Aalborg H/HW boilers are available with vertical or horizontal layouts. The Aalborg H, which is used for steam generation, has an integrated steam space and employs natural circulation. The Aalborg HW, which is used in hot water applications, has flow-optimizing baffle plates and employs forced circulation.

What Can I Do For You?

Send us your inquiry
Leave Us Message

You can send a message to us by this email to zhulin@zozen.com

If you have any problems about our product and service,please feel free to give your inquiry in the form below. We will reply you within 24 hours as soon as possible.Thank you!

  • Boiler type
  • Name
  • email
  • Phone or Whatsapp
  • message
I accept the Data Protection Declaration
Are You Looking for A Consultant? ONLINE SERVICE
totop