We founded in 1988, with 32 years'experience in research development and manufacture of industrial boiler. Our boiler are saled for more than 100 countries and regions like Egypt, Ethiopia, Congo, Mauritius, Tanzania,South Africa, Mexico, Ireland, Indonesia etc.
7*24 hours online service：email@example.comGet Free Quote
Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Product Thermal Capacity: 20 - 110 t/h
Working Pressure: 1.25 - 5.3 Mpa
Product Thermal Capacity: 2 – 20t/h
Working Pressure: 1 - 2.5 MPA
Product Thermal Capacity: 4 - 35 t/h
Working Pressure: 1.0 - 2.5 MPA
Basic Water (> 8.5 pH) Water with a high pH isn't quite as problematic as water with low pH, but does have its issues. Among them is hard water - water with high levels of minerals (mainly calcium and magnesium). Hard water typically has a high pH because the minerals in …
Jan 26, 2018· > Natural water is usually between 6.5 and 7.5 pH. A common recommendation is to maintain boiler water at 8.5 pH.Acidic water is corrosive. Alkalinic water is more prone to scaling.Alkalinity is a measure of the bicarbonate (HCO3), carbonate (CO3
Boiler Water Treatment Part 2 – Internal Treatment Objectives of Internal Water Treatment 1 – To control the level of total dissolved solids (TDS) within the boiler As water is boiled within the boiler and steam is produced, then the solids remain in the water and concentrate. Thus, over time the level of total dissolved solids (TDS) increases.
The Best pH Level for Drinking Water Explained Once & for All G ood morning fellow health nuts, it’s your host, Hercules, back in action after a few days on the road. This morning, I will discuss the ideal pH level for drinking water and why it is so important not to go overboard when drinking alkaline ionized water.
Learn more Apr 07, 2011· I have to lower the PH of my boiler water. I can use Hydrochloric acid (also known as muriatic acid) or Sodium Bisulfate to lower the pH levels in water. Both are recommended for lowering PH. Would one be better to use than the other. Any information would be appreciated.
Inexplicable pH drop in boiler blowdown water. A discussion started in 2004 but continuing through 2019. 2004. Q. This question pertains to drop in pH of blowdown water of a low pressure steam boiler. In one of the waste heat recovery boilers, (operates at 180 °C), pH of the blow down water drops to 5 and even 4.
How much Sodium Hydroxide needed to raise boiler water pHSep 28, 2015How to get rid of water corrosion | Hearth.com Forums HomeSep 18, 2014Boiler Water PH | Hearth.com Forums HomeApr 04, 2011Water Quality and Nitrite Test ( Need Help) | Hearth.comFeb 23, 2011See more results In high-purity systems, raw water in-leakage (e.g., condenser leakage) lowers boiler water pH when magnesium hydroxide precipitates, resulting in corrosion, formation of atomic hydrogen, and initiation of hydrogen attack. Coordinated phosphate/pH control can be used to minimize the decrease in boiler water pH that results from condenser leakage.
Click to view1:17Nov 07, 2016· Keep the corrosion to a minimum in your steam boiler? Keep the pH between 8.5 and 9.5 Here is how you check the pH of your boiler water. Easily done. No problem. Take a look.
For new boiler installations, the system is often precleaned prior to service with a high pH boiler chemical cleaner. This procedure is referred to as boiler “boil out” . This chemical is a corrosion inhibited, high alkaline product that is added directly to the boiler water and recirculates.
You can send a message to us by this email to firstname.lastname@example.org
If you have any problems about our product and service,please feel free to give your inquiry in the form below. We will reply you within 24 hours as soon as possible.Thank you!